Geology Wiki

Transform fault

519pages on
this wiki
Add New Page
Talk0 Share

A transform fault or transform boundary, also known as conservative plate boundary since these faults neither create nor destroy lithosphere, is a type of fault whose relative motion is predominantly horizontal in either sinistral or dextral direction. Furthermore, transform faults end abruptly and are connected on both ends to other faults, ridges, or subduction zones.[1] While most transform faults are hidden in the deep oceans where they form a series of short zigzags accommodating seafloor spreading (see graphic at right), the best-known (and most destructive) are those on land at the margins of tectonic plates. Transform faults are the only type of strike-slip fault that can be classified as a plate boundary. Transform faults show up on the seafloor as valleys that may be even deeper than the rift valleys of spreading ridges.

Background Edit

John Tuzo Wilson recognized that the offsets of oceanic ridges by faults do not follow the classical pattern of an offset fence or geological marker in Reid’s rebound theory of faulting,[2] from which the sense of slip is derived. The new class of faults,[3] called transform faults, produce slip in the opposite direction from what one would surmise from the standard interpretation of an offset geological feature. Slip along transform faults does not increase the distance between the ridges it separates; the distance remains constant in earthquakes because the ridges are spreading centers. This hypothesis was confirmed in a study of the fault plane solutions that showed the slip on transform faults points in the opposite direction than classical interpretation would suggest.[4]

Difference between transform and transcurrent faultsEdit

Transform faults are closely related to transcurrent faults. Both types of faults are strike-slip or side-to-side in movement, (see diagrams to the right) however transform faults end at the junction of another plate boundary or fault type, while transcurrent faults die out without a junction. In addition, transform faults have equal deformation across the entire fault line, while transcurrent faults have greater displacement in the middle of the fault zone and less on the margins. Finally, transform faults can form a tectonic plate boundary, while transcurrent faults cannot.

File:Transform fault.jpg
File:Transcurrent NEW.jpg


The effect of a fault is to relieve strain, which can be caused by compression, extension, or lateral stress in the rock layers at the surface or deep in the Earth’s subsurface. Transform faults specifically relieve strain by transporting the strain between ridges or subduction zones. Transform faults also act as the plane of weakness allowing for the splitting in rift zones.


Transform faults are commonly found linking segments of mid-oceanic ridges or spreading centers. These mid-oceanic ridges are where new sea floor is constantly created through the up welling of new basaltic magma. With new sea floor being pushed and pulled out, the older sea floor slowly slides away from the mid-oceanic ridges toward the continents. Although, separated only by tens of kilometers, this separation between the ridges causes the sea floor to be pushed pass each other in opposing directions. This lateral movement of sea floors past each other is where transform faults are currently active. Spreading center and strips

Transform faults move differently than a strike-slip fault at the mid-oceanic ridge. Instead of the ridges moving away from each other, like other strike-slip faults, transform fault ridges will stay in the same fixed location, and the new ocean sea floor being created at the ridges is pushed away from the ridge. The proof of this is found in paleo-magnetic striping on the sea floor.

A paper written by Gerya theorizes that the creation of the transform faults between the ridges of the mid-oceanic ridge is attributed to rotated and stretched sections of the mid-oceanic ridge.[5] This occurs over long period of time with the spreading center or ridge slowly deforming from a straight line to a curved line and then finally fracturing along these planes forming transform faults. As this takes place, the fault changes from a normal fault with extensional stress to a strike slip fault with lateral stress.[6] In the study done by Bonatti & Crane, peridotite and gabbro rocks were discovered in the edges of the transform ridges. These rocks are created deep inside the Earth’s mantle and then rapidly exhumed to the surface.[6] This evidence helps to prove that new sea floor is being created at the mid-oceanic ridges and further supports the theory of plate tectonics.

As previously stated, active transform faults are between two tectonic structures or faults. Fracture zones represent the previously active transform fault lines, which have since passed the active transform zone and are being pushed toward the continents. These elevated ridges on the ocean floor can be traced for hundreds of miles and in some cases even from one continent across an ocean to the other continent.

The most prominent examples of the mid-oceanic ridge transform zones are located in Atlantic Ocean between South America and Africa. Known as the St. Paul, Romanche, Chain, and Ascension fracture zones, these areas have with deep, easily identifiable transfrom faults and ridges. Other locations include: the East Pacific Ridge located in the South Eastern Pacific Ocean, which meets up with San Andreas Transform fault to the North.

Transform faults are not limited to oceanic crust and spreading centers; many transform faults are located on continental margins. The best example is the San Andreas fault on the Pacific coast of the United States. The San Andreas Fault links the East Pacific Rise off of the West coast of Mexico (Gulf of California) to the Mendocino Triple Junction (Part of the Juan de Fuca plate) located off the coast of the North Western United States making it a ridge-to-transform style transform fault. [3] The formation of the San Andreas Fault system occurred fairly recently during the Oligocene Period between 34 million and 24 million years ago.[7] During this period, the Farallon plate, followed by the Pacific plate, collided into the North American plate.[7] The collision led to the subduction of the Farallon plate underneath the North American plate. Once the spreading center separating the Pacific and Farallon plate was subducted underneath the North American plate, the San Andreas Continental Transform Fault system was created.[7]

File:Alpine Fault SRTM.jpg

Other examples include:

Transform fault typesEdit

In his groundbreaking work on transform fault systems, Tuzo Wilson said that transform faults must be connected to other faults or tectonic plate boundaries on both ends; because of that requirement, transform faults can grow in length, keep a constant length, or decrease in length.[3] These length changes are dependant on which type of faults or tectonic structures connect with the transform fault. With this in mind, Wilson described six types of transform faults:

Growing length faults: In situations where a transform fault links together a spreading center and the upper block of a subduction zone or when two upper blocks of subduction zones are linked the transform fault itself will grow in length.[3]

Spreading to upper NEW Upper to upper

Constant length faults: In other cases, transform faults will remain at a constant length. This consistency can be attributed to many different reasons. In the case of a ridge-to-ridge transforms, it is caused by the continuous growth by both ridges outward, canceling any change in length. The opposite occurs when a ridge linked to a subducting plate, where all the lithosphere (new sea floor) being created by the ridge is being subducted, or swallowed up, by the subduction zone.[3] Finally, when two upper subduction plates are linked there is no change in length. This is due to the plates moving parallel with each other and no new lithosphere is being created to change that length.

Spreading centers constant Upper to down NEW Spreading to Down NEW

Decreasing length faults: In rare cases, transform faults can shrink in length. These occur when two descending subduction plates are linked by a transform fault. In time as the plates are subducted, the transform fault will decrease in length until the transform fault disappears completely, leaving only two subduction zones facing in opposite directions.[3]

Down to down NEW

See also Edit



  • International Tectonic Dictionary - AAPG Memoir 7, 1967
  • The Encyclopedia of Structural Geology and Plate Tectonics - Ed. by Carl K. Seyfert, 1987

Template:Physical oceanography

Cite error: <ref> tags exist, but no <references/> tag was found

Ad blocker interference detected!

Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.